Skip to content
East Valley (480) 571-5944 · Northern AZ (928) 813-0825 · Open 24 hours, seven days. $300 off tankless water heater installation → · Finance now →

Tankless Water Heater

Tankless Water Heater Maintenance & Tune-Up in Scottsdale, AZ

Restoring Hot Water Flow and Maintaining Your Tankless Water Heater in Scottsdale

Is your tankless water heater suddenly dropping water pressure when two showers are running, flashing an error code on the remote panel, or delivering a frustrating cold water sandwich during your morning routine? This isn't necessarily a sign that your unit is completely broken, but rather a symptom of Scottsdale's notoriously hard water baking mineral scale onto the internal heat exchanger. Gold Star Plumbing & Drain is ready to flush your system, clear out the mineral buildup, and restore your unit to full heating capacity before permanent damage occurs.

Warning Signs Your Tankless Water Heater Needs Maintenance

Sudden Drops in Hot Water Pressure

You turn on the shower and notice the water pressure is noticeably weaker than it used to be, especially if a dishwasher or washing machine is running at the same time. Tankless units have internal flow sensors and bypass valves to carefully control output temperature. When the heat exchanger becomes coated in mineral scale, the unit physically cannot heat water fast enough and intentionally restricts the flow rate to compensate.

If ignored, the unit will continue to choke off water pressure until it eventually shuts down completely. This is a built-in safety measure designed to prevent the heat exchanger from melting or cracking under the immense strain. Restoring normal flow requires a comprehensive internal descaling to remove this physical barrier.

Flashing Error Codes on the Control Panel

The remote control panel or the digital display on the unit itself starts beeping and flashing a two-digit code, causing the hot water to shut off completely. These codes are the system's diagnostic language, most commonly indicating scale buildup in the heat exchanger, a blocked exhaust vent, or an ignition failure. Resetting the unit by unplugging it might provide a temporary fix, but the internal safety sensors will quickly trip again.

Continuing to force the unit to run with an active error code is incredibly risky for the equipment. It can easily void the manufacturer's warranty and cause catastrophic failure of the internal components. A professional tune-up addresses the root cause of the code rather than just temporarily clearing the screen.

Fluctuating Temperatures and Cold Water Sandwiches

You experience a blast of hot water, followed by a sudden freezing cold shock, followed by hot water again. This frustrating cycle happens when a dirty flow sensor fails to register that water is moving, causing the burner to shut off momentarily. It can also occur if the inlet water filter is clogged with sediment from the municipal supply, causing erratic flow readings.

Beyond being incredibly uncomfortable, this erratic firing puts unnecessary wear and tear on the gas valve and ignition system. The constant cycling stresses the electronic components and shortens the overall lifespan of the unit. Proper maintenance cleans these sensors so the unit can read water flow accurately and maintain a steady temperature.

Unusual Rumbling or Whining Noises

When the hot water is turned on, a loud rumbling, popping, or high-pitched whining noise comes from the unit mounted on your wall. This is the sound of water boiling and bubbling through a thick layer of calcium scale inside the narrow copper or stainless steel tubing of the heat exchanger. The high-pitched whine is often the combustion fan struggling against a dirty air intake.

A noisy tankless water heater is a stressed system that is working much harder than it was designed to. The longer it runs in this condition, the higher your utility bills will climb as it wastes energy trying to heat water through solid rock. Routine maintenance quiets the system down by removing the obstructions causing the noise.

Common Causes of Tankless Water Heater Problems

Severe Mineral Scale Accumulation

Calcium and magnesium minerals precipitate out of the water when heated, clinging to the metallic walls of the heat exchanger and forming a rock-hard layer of scale. Scottsdale features extremely hard water, making this the primary cause of tankless water heater issues in local homes. Without regular flushing, scale builds up much faster here than in regions with softer municipal water.

The solution involves isolating the unit from the home's plumbing and circulating a specialized descaling solution through the heat exchanger. We run this flush for about an hour to completely dissolve the baked-on minerals. This process strips the scale away and exposes the bare metal of the heat exchanger so it can transfer heat efficiently again.

Clogged Inlet Water Filters

Debris, sand, and small particulates get trapped in the mesh screen located exactly where the cold water line enters the tankless unit. Local municipal water lines and aging city infrastructure occasionally kick up sediment that travels straight into your home's plumbing. When this sediment hits the fine mesh filter of a tankless unit, it acts like a physical plug blocking incoming water.

A professional tune-up involves shutting off the water supply and carefully removing this inline filter. We clean out the trapped sediment and inspect the internal O-rings before reinstalling it to restore proper water flow. This simple step often dramatically improves water pressure at your highest-demand fixtures.

Dirty Air Intake and Exhaust Vents

The fan that pulls in fresh air for combustion and pushes out exhaust gases becomes coated in dust, dirt, or debris over time. The dry, dusty conditions of the Arizona desert mean that exterior-mounted units suck in a significant amount of airborne particulate. This dust rapidly coats the fan blades and clogs the vital intake screens needed for clean combustion.

The maintenance process includes removing the front cover to carefully inspect the entire fan assembly. We vacuum and brush away the accumulated dust to ensure a clean, efficient fuel burn. A clean fan prevents the unit from suffocating and prevents dangerous exhaust gases from backing up.

Fouled Flame Rods and Igniters

The metal rod that sparks to light the gas, or the sensor that proves a flame is present, becomes coated in carbon buildup or white silica dust. When combustion air carries local desert dust into the burner chamber, it literally burns onto these sensitive electronic sensors. If the flame rod gets too dirty, it cannot conduct the electrical current needed to tell the computer that the flame is actively lit.

This causes the gas valve to shut off immediately as a safety precaution, leaving you with no hot water. A professional tune-up involves carefully removing the igniter assembly and polishing the metal probes clean. We then test the microamp readings to ensure reliable, consistent ignition every time you open a tap.

What to Expect During Your Service Visit

Diagnostics and Preparation

When Gold Star Plumbing & Drain arrives at your Scottsdale property, we start by checking the digital controller for any stored error codes in the unit's history. This gives us a clear picture of exactly how the system has been struggling over the past few months. We then shut off the gas and water, connecting a submersible pump and heavy-duty hoses to the unit's isolation valves.

The Descaling Process

A descaling solution is pumped directly through the heat exchanger for roughly an hour to break down all internal mineral buildup. We monitor the solution as it circulates, watching for the telltale signs of dissolved calcium being flushed out of the system. While the flush is actively running, we clean the cold water inlet filter, inspect the venting system, and clean the flame sensor and ignition rods.

Final Testing and Verification

Once the descaling process is complete, the system is thoroughly flushed with clean water to remove any remaining acidic solution. We reconnect all the lines, turn the gas back on, and test-fire the water heater to observe its performance in real-time. We verify that the gallons-per-minute flow rate and temperature rise perfectly meet the manufacturer specifications before we consider the job done.

Related Services You May Need

To permanently protect a tankless water heater from hard water and reduce the frequency of intense descaling, we highly recommend looking into Water Softener Installation & Replacement. If the heat exchanger is already leaking or a component has failed completely due to lack of maintenance, a standard tune-up will not fix it. In those severe cases, we will guide you through our Tankless Water Heater Repair & Service options to replace the damaged parts and get your hot water back online. We can also assist with comprehensive Water Heater Maintenance & Tune-Up for traditional tank systems on the property.

The True Cost of Delaying Maintenance

Voided Manufacturer Warranties

Almost all major tankless water heater brands strictly require proof of annual maintenance by a licensed professional to keep their coverage active. If your heat exchanger cracks due to excessive scale buildup, the manufacturer will likely deny the warranty claim entirely. Routine maintenance is the only reliable way to protect this valuable warranty coverage and avoid paying out of pocket for major repairs.

Catastrophic Heat Exchanger Failure

The heat exchanger is the absolute heart of your on-demand water heating system. If it becomes completely blocked or cracks from overheating, the replacement part often costs nearly as much as a brand new water heater. Preventative flushing removes the stress that causes these crucial components to fail prematurely.

Wasted Energy and High Bills

A scaled-up unit has to burn significantly more natural gas or use more electricity to heat water through an insulating layer of solid calcium. This forces the system to work overtime just to produce lukewarm water for your showers and sinks. Keeping the heat exchanger clean ensures maximum energy efficiency and keeps your monthly utility bills under tight control.

Schedule Your Tankless Water Heater Tune-Up Today

Preventative maintenance is the only way to ensure your high-demand plumbing fixtures continue to receive endless hot water. Don't wait for flashing error codes to leave you taking cold showers when a simple service visit can restore your system's performance. Gold Star Plumbing & Drain provides expert, thorough tankless tune-ups throughout the area to keep your system running flawlessly. Call us today to book your maintenance visit and restore your home's hot water capacity.

Tell us what it is doing.

Submit your request and a member of the Gold Star team will call you as soon as possible to answer your questions and schedule your service. If water is moving right now, call instead. A person answers.

Hours
Open 24 hours, seven days
Licence
Arizona ROC 327327

Book a time online

Pick a slot and it is a confirmed appointment, not a request.

Rather talk it through? Call (480) 571-5944 — a person answers, every hour of every day.

Or tell us what is going on

Send it through and a member of the Gold Star team will call you back to answer your questions and schedule the work.

Request Your Service

Submit your request and a member of the Gold Star team will call you as soon as possible to answer your questions and schedule your service. Need help now? Call: emergency plumbers are dispatched 24/7.

Loading form. If it does not load, please use the other contact options on this page.

How we use your information: Privacy Policy · Your Privacy Choices

Call now Book online