Skip to content
East Valley (480) 571-5944 · Northern AZ (928) 813-0825 · Open 24 hours, seven days. $300 off tankless water heater installation → · Finance now →

Tankless Water Heater

Tankless Water Heater Repair & Service in San Tan Valley, AZ

Solving Temperature Drops and Error Codes: Tankless Water Heater Repair in San Tan Valley

Are you getting blasted with cold water in the middle of a hot shower, noticing a severe drop in hot water pressure, or staring at a flashing error code on your tankless unit's control pad? Tankless systems are highly engineered pieces of equipment, and when they start acting up, it means a sensor is failing, airflow is blocked, or our notoriously hard local water has caused mineral scale to build up to a critical level inside the heat exchanger. When your on-demand hot water stops demanding, the team at Gold Star Plumbing & Drain is ready to troubleshoot the exact error code and restore your hot water safely.

Warning Signs Your Tankless Water Heater Needs Attention

The Cold Water Sandwich

You turn on the shower, feel hot water, and then suddenly get hit with a wave of freezing cold water before it turns hot again. This frustrating experience usually means the unit's flow sensor is failing to register the continuous demand for water, or the burner is struggling to maintain a consistent flame. In many cases, scale buildup is interfering with these sensitive sensors and throwing off the temperature readings.

If ignored, these temperature fluctuations will become more frequent until the unit fails to heat water entirely. You are forcing the system to constantly recalibrate, which puts unnecessary wear on the internal computer.

Unexplained Drops in Hot Water Pressure

The cold water flows from the tap at full blast, but when you turn the handle to hot, the water slows down to a frustrating trickle. This is a physical blockage indicating that mineral scale has choked the internal plumbing of the heat exchanger, or the inlet water filter is completely clogged with debris. Running a tankless unit with restricted flow causes it to overheat rapidly as it tries to hit the target temperature.

Modern units will eventually trigger a safety shutdown to protect themselves from this excess heat. Older units, however, may suffer permanent heat damage if this restricted flow continues.

Flashing Error Codes or Beeping

The digital display on the unit or your remote temperature controller starts flashing a two-digit number, like 11, 12, or 90, and may emit a continuous beeping sound. These codes are the system's built-in diagnostics telling you exactly what is wrong, whether it is an ignition failure, a blocked exhaust vent, or abnormal combustion. Resetting the unit by unplugging it might clear the code temporarily, but it does not fix the root cause.

The unit will continue to lock you out to prevent a catastrophic failure or a serious gas hazard. Ignoring an error code is the fastest way to turn a simple sensor replacement into a major system failure.

Strange Rumbling or Whining Noises

When a hot water tap is opened, the unit outside or in your garage makes a loud whining sound, a rumbling vibration, or repeated clicking without actually firing up. Clicking usually means the igniter is trying to light the gas, but the flame sensor is not registering it. Rumbling or whining often points to a failing fan motor or water boiling inside a scale-coated heat exchanger, which is known as kettling.

These noises indicate severe mechanical strain that needs immediate attention from a professional. Left unaddressed, you will likely face a burned-out motor or a cracked combustion chamber.

What is Causing Your Tankless Water Heater Problems?

Severe Mineral Scale Buildup

Hard water minerals precipitate out of the water when heated, clinging tightly to the copper or stainless steel walls of the heat exchanger. Over time, this forms a thick, rock-like barrier that prevents heat from transferring to the water efficiently. San Tan Valley is notorious for its extremely hard water, and because tankless units flash-heat water at high temperatures, they accumulate scale much faster than traditional tank heaters.

The solution involves isolating the unit and pumping a specialized, professional-grade descaling solution through the system. We circulate this solution for about an hour to fully dissolve the minerals and clear the narrow passages.

Blocked Air Intakes or Exhaust Vents

Your system cannot pull in enough fresh air for combustion, or it cannot properly vent the exhaust gases, causing the computer to shut down the burners for safety. Because many homes in San Tan Valley feature exterior-mounted tankless units, airborne dust, dirt, and debris from local winds frequently clog the protective intake screens. The system simply cannot breathe properly to sustain a safe, consistent flame.

We will disassemble the housing, clean the fan and intake screens, and check the exhaust venting for any hidden obstructions. After everything is cleared, we recalibrate the air-fuel mixture if necessary to ensure clean combustion.

Dirty or Failing Flame Sensors

The unit successfully opens the gas valve and sparks the igniter, but the flame sensor is coated in carbon or dust and cannot detect the fire. When this happens, the system immediately shuts off the gas to prevent a dangerous leak from filling the cabinet. The dusty environment outside your home, combined with normal combustion byproducts, commonly coats these sensitive electrical probes over time.

Fixing this requires carefully removing the burner assembly and cleaning the delicate sensor rods with a specialized abrasive pad. If the sensor harness has shorted out entirely, we will replace the component to restore proper ignition.

Clogged Inlet Water Filters

Debris from the municipal water supply or deteriorating pipes gets caught in the small mesh filter located right where the cold water enters your unit. High mineral content in the local water supply often leads to sediment breaking loose and clogging this tiny filter, preventing enough water from entering the unit. If the unit does not sense enough water moving through, it will not turn on the burners to heat it.

We will shut off the water supply, remove and clean the inline screen, and test the flow rate. This ensures the unit activates properly even at low demands, like running a single bathroom sink.

What to Expect During Your Tankless Water Heater Repair Visit

Detailed Diagnostics and Isolation

We start by checking the digital display for error codes, testing the flow rate at your fixtures, and inspecting the unit's exterior housing and venting. Tankless systems require a methodical approach, so we look at the entire picture before taking anything apart. Next, we shut off the gas, water, and power to safely isolate the unit and begin testing internal components.

We use a multimeter to test electrical parts like the flow sensor, igniter, and fan motor. This helps us pinpoint exactly where the communication or mechanical breakdown is happening.

Precision Repair and High-Demand Testing

Whether your system requires replacing a faulty sensor, cleaning the burner assembly, or performing an intensive flush to remove scale, we handle the repair with precision. Once the faulty component is addressed, the system is fully reassembled and prepped for testing. We then run the unit through a high-demand test by opening multiple hot water taps in your home to ensure the water stays consistently hot under pressure.

Gold Star Plumbing & Drain provides these targeted diagnostics and repairs for homeowners throughout San Tan Valley, ensuring your system operates safely. We do not guess at the problem; we find the exact failure point and fix it.

Protecting Your Plumbing and Water Heating Systems

Long-Term Solutions for Hard Water

If mineral scale buildup is the primary cause of your system failure, investing in Water Softener Installation & Replacement is the absolute best way to protect your repaired tankless unit. Soft water prevents scale from forming entirely, protecting the heat exchanger and the rest of your home's plumbing from our harsh local water. We also highly recommend scheduling routine Tankless Water Heater Maintenance & Tune-Up services to keep your system running smoothly year after year.

Annual flushing is required by almost all manufacturers to keep your warranties valid and prevent these frustrating breakdowns. Staying ahead of the scale buildup is the key to getting the full lifespan out of your investment.

The True Cost of Ignoring Tankless Water Heater Issues

Expensive Damage and Voided Warranties

When scale builds up inside the heat exchanger, the heat cannot transfer to the water and gets absorbed by the surrounding metal instead. The heat exchanger eventually warps and cracks under this intense stress, leaving you to replace the most expensive part of the entire unit. Ignoring these issues also puts your manufacturer warranty at serious risk.

Almost all tankless water heater manufacturers stipulate that the unit must be kept free of scale and properly maintained by a professional. If a part fails due to neglect, your warranty claim will be denied, leaving you to pay out of pocket for a preventable failure.

Total Loss of Hot Water

Tankless units are designed with strict safety protocols that will shut the system down entirely when they detect an issue like poor venting or ignition failure. They do this to protect your home from gas leaks, exhaust buildup, or fire hazards. Waiting to call a professional simply guarantees you will eventually be stuck without hot water when you need it most.

These units do not heal themselves, and a flashing error code will eventually become a permanent lockout. Addressing the problem early keeps a minor repair from turning into a complete unit replacement.

Ready to Restore Your Endless Hot Water?

Tankless systems require specialized knowledge, and ignoring those early warning signs or error codes only leads to much more expensive repairs down the line. Prompt, professional troubleshooting can save your unit from premature failure and get your daily routine back to normal. The experts at Gold Star Plumbing & Drain are ready to get your San Tan Valley tankless water heater running efficiently again.

Tell us what it is doing.

Submit your request and a member of the Gold Star team will call you as soon as possible to answer your questions and schedule your service. If water is moving right now, call instead. A person answers.

Hours
Open 24 hours, seven days
Licence
Arizona ROC 327327

Book a time online

Pick a slot and it is a confirmed appointment, not a request.

Rather talk it through? Call (480) 571-5944 — a person answers, every hour of every day.

Or tell us what is going on

Send it through and a member of the Gold Star team will call you back to answer your questions and schedule the work.

Request Your Service

Submit your request and a member of the Gold Star team will call you as soon as possible to answer your questions and schedule your service. Need help now? Call: emergency plumbers are dispatched 24/7.

Loading form. If it does not load, please use the other contact options on this page.

How we use your information: Privacy Policy · Your Privacy Choices

Call now Book online