Skip to content
East Valley (480) 571-5944 · Northern AZ (928) 813-0825 · Open 24 hours, seven days. $300 off tankless water heater installation → · Finance now →

Symptom Center

No Hot Water, or It Runs Out Fast? Causes and What to Do

A heater losing hot water this way usually fails completely within days. Get it checked today.

Same day Not dangerous, but a heater that is failing this way usually fails completely within days.

Book Online

Symptom Center · 5 min read

By Mike Smith , Owner, Gold Star Plumbing & Drain · LinkedIn

Losing hot water is one of the most common reasons people call a plumber. Sometimes it goes all at once. More often it fades: showers turn lukewarm sooner than they used to, or the water takes longer to heat back up. Both are signs the heater is struggling.

The cause depends on whether you have a gas, electric or tankless unit. Here is what to check, what a plumber looks at, and how to think about repair versus replacement. If you are not sure which kind you have, our guide to water heater types will help you tell.

Why did my hot water stop or start running out?

On electric units, a failed heating element or thermostat. On gas units, a pilot, thermocouple or gas valve fault. On any tank in Arizona, sediment from hard water can fill the bottom of the tank.

An electric tank usually has two heating elements, each with its own thermostat. When the upper one fails, you get no hot water. When the lower one fails, you get a little hot water that runs out quickly. A gas tank depends on a pilot or igniter, a thermocouple that confirms the flame is lit, and a gas valve. If any of those fail, the burner will not fire.

Sediment is the slow version. Arizona water carries a lot of calcium and magnesium, and heat drops it to the bottom of the tank. It takes up space and blankets the burner, so there is less hot water and it takes longer to recover. Our hard water guide explains why this happens so often here.

  • Electric: a failed upper or lower element, or a thermostat fault
  • Gas: the pilot is out, a bad thermocouple, or a gas valve fault
  • Tankless: scale in the heat exchanger, or an error code shutting it down
  • Any tank: sediment buildup, or a broken dip tube mixing cold water into the hot
  • A tripped breaker, or a gas supply valve that was turned off

What can I safely check before calling?

Check the breaker on an electric unit, the pilot or status light on a gas unit, and the display for an error code on a tankless unit.

For an electric heater, look at its breaker. If it has tripped, reset it once. If it trips again, leave it off, because that points to a failed element or wiring fault. For a gas heater, check the sight window or status light. If the pilot is out and the label on the tank gives relighting steps, you can follow them, but only if you smell no gas. If you do smell gas, leave the house and call the gas utility from outside.

For a tankless unit, write down any error code on the display. That code tells the plumber where to start. Also make sure the gas valve to the heater is open and the outlet or switch that powers it is on.

If none of that brings the hot water back, stop there. Relighting or resetting again and again can hide a problem that needs a part.

What does the plumber check first?

We test the elements and thermostats, check the burner and venting on a gas unit, and drain a sample to see how much sediment has built up.

On an electric unit, we test each element and thermostat to find the one that failed. On a gas unit, we check the pilot assembly, the thermocouple, the gas valve and the venting, because a heater that cannot vent safely should not be running. On a tankless unit, we read the error history and check the heat exchanger for scale.

Draining a sample shows how much sediment is sitting at the bottom of the tank. That, along with the age on the data plate, helps answer whether this is a simple part on a healthy tank or a sign an older tank is near the end. Same-Day Service Available.

Should I repair it or replace it?

Repair a failed part on a sound tank. Replace when the tank is old, packed with sediment, or failing in more than one way.

Elements, thermostats, thermocouples and gas valves are serviceable parts, and our water heater repair service covers them. When the tank itself is near the end of its life, replacement is often the better use of your money. Our repair or replace framework and our guide to water heater lifespan in Arizona walk through the decision.

If you do replace, it is worth asking whether a tankless or heat-pump model fits your house better. Three Clear Options. No Pressure. You see each option with upfront pricing and approve one before work starts. Financing Options Available through GreenSky.

Quick answers

Why do I have hot water in some rooms but not others?
If one fixture runs cold and the rest are fine, the problem is likely that fixture's mixing valve or cartridge rather than the heater. A shower that suddenly runs only warm is a common example.
Does a pilot that keeps going out mean the heater is failing?
Not necessarily. A worn thermocouple or a dirty pilot assembly is a common, repairable cause. It tips toward replacement only when the tank is also old or other problems are stacking up.
How long does a water heater last in Arizona?
Hard water tends to shorten tank life here compared with softer-water states, and maintenance such as yearly flushing and anode checks makes a real difference. The age on the data plate is a useful starting point when deciding what to do.

Next step

Lukewarm showers or no hot water at all? Book a visit. We find the failed part and tell you straight whether the tank is worth repairing.

Water heater repair
Call now Book online