Step 01 · Learn · 5 min read
By Mike Smith
, Owner, Gold Star Plumbing & Drain ·
LinkedIn
Most Arizona houses are built right on a concrete slab, with water lines running in the ground under the floor. When one of those lines springs a leak, you have a slab leak: a leak you cannot see, under a floor you do not want to open.
Slab leaks sound alarming, but they are well understood and very fixable. Here is what they are, how they get found, and the choices you have once one is confirmed. If you suspect one right now, start with the meter test.
What exactly is a slab leak?
A leak in a pressurized water line that runs under or through the concrete slab your house sits on. It is usually a supply line, hot or cold, not a drain.
In a slab-on-grade house, the water lines are often laid in the soil before the slab is poured, then rise through the concrete to each fixture. Many Valley homes have copper under the slab. Because those lines carry water under pressure, even a pinhole keeps leaking every hour of the day.
Drain lines run under the slab too, and they can crack or separate, but a drain only leaks when water goes down it. When plumbers say slab leak, they usually mean a pressurized supply line, and that is what this guide covers.
Why do slab leaks happen here?
The pipe is worn from both sides: by hard, hot water moving through it, and by soil and slab movement around it.
Our hidden leak guide covers the main causes. In short, mineral-heavy water moving at speed wears copper from the inside, reactive soil can pit it from the outside, and seasonal ground movement flexes the line. Pipes can also rub against concrete or gravel where they pass through the slab, and a small installation flaw can take years to show up.
Hot lines tend to fail more often than cold ones, because heat speeds up the wear. High water pressure adds stress at every joint and weak spot. And when a house has had one slab leak, the same pipe is aging everywhere else under the floor too, which matters when you choose how to fix it.
What are the signs of a slab leak?
A warm spot on the floor, a water bill that climbs for no reason, the sound of running water when everything is off, or damp flooring with no visible source.
A hot-line leak often shows up as a patch of tile or concrete that feels warm underfoot, or a water heater that seems to run all the time. A cold-line leak is quieter and is usually caught by the bill. Other clues include a damp carpet pad, warped wood flooring, a musty smell, or new cracks in tile. Our hidden leak symptom page walks through what to check first.
No single sign proves a slab leak. Several together, especially a warm spot plus a rising bill, are a strong reason to test.
How is a slab leak found?
In steps: the meter test proves water is being lost, then a plumber narrows down which line and where, so any opening in the floor is as small as possible.
The first step you can do yourself. The meter test tells you whether water is leaving the system with everything off, and closing the house shutoff tells you whether the loss is inside the house or out in the yard line. Write down the readings and the times. They help the plumber.
From there, professional leak detection works by elimination: ruling out toilets, the water heater, a softener and irrigation, separating the hot side from the cold side, and narrowing the leak down to a section of pipe before anything is opened. The goal is a confirmed location, not a guess with a jackhammer.
Should the leak be repaired or the line rerouted?
Both are common. A spot repair fixes the one leak through the slab. A reroute retires the leaking line and runs a new one through the walls or attic instead.
A spot repair means opening the floor at the leak, fixing that section of pipe and closing the concrete back up. It makes sense for a first leak on pipe that is otherwise in fair shape, when the spot is reasonable to reach. The downside is that it fixes one point on a pipe that is the same age everywhere.
A reroute leaves the old line in place, disconnected, and runs new pipe through the walls or attic to the fixtures it served. It avoids breaking the slab and takes that run of old pipe out of the picture for good. When leaks keep coming back in different places, the conversation moves to whole-house repiping, which Gold Star does with copper or PEX-A. Our slab leak repair page covers each approach, and the choice is yours: Three Clear Options. No Pressure.
- Spot repair: one leak, sound pipe, reachable location.
- Reroute: leak in a hard-to-reach spot, or a line you would rather retire than patch.
- Repipe: repeat leaks in different places on pipe of the same age.
Quick answers
- Can a slab leak damage my foundation?
- It can if it runs long enough. Water running under a slab can soften or wash away the soil beneath it. That is the reason to act once the meter test points to a leak, rather than waiting to see if it gets worse.
- How much of my floor will have to be opened?
- With a spot repair, usually one section over the leak, once the location is narrowed down. With a reroute, the floor usually stays closed and the work happens through small openings in walls and ceilings instead.
- Water is coming up through the floor. What do I do?
- Close the main house shutoff right away and call. Water actively surfacing is an active leak, which Gold Star treats as a plumbing emergency.
Next step
Slab leak repair