Skip to content
East Valley (480) 571-5944 · Northern AZ (928) 813-0825 · Open 24 hours, seven days. $300 off tankless water heater installation → · Finance now →

Symptom Center

Low Water Pressure in the House? Common Causes and Fixes

Usually a book-ahead problem, unless pressure drops everywhere at once.

Book ahead Usually a book-ahead problem. A sudden drop across the whole house is different and can mean a broken line.

Book Online

Symptom Center · 4 min read

By Mike Smith , Owner, Gold Star Plumbing & Drain · LinkedIn

Weak water pressure creeps up on you. The shower feels thinner, the washing machine takes longer to fill, and the kitchen sink trickles while someone else runs water. In most homes it has a fixable cause, and the first job is figuring out whether the problem is one fixture or the whole house.

One exception up front: if pressure dropped everywhere at once, with no warning, treat it as urgent. A sudden whole-house drop can mean a burst pipe or a break in the main line, so check your water meter and read our page on losing water to the whole house.

Is it one fixture or the whole house?

One fixture points to that fixture's aerator, shower head or cartridge. The whole house points to the pressure-reducing valve, the main shutoff, the pipes or the utility.

Walk through the house and test each sink, shower and tub on both hot and cold. If only one is weak, the problem is almost always at that fixture. If everything is weak, the problem is upstream, somewhere between the meter and your fixtures. If only the hot side is weak everywhere, the water heater or its valves are the likely suspects.

Ask a neighbor too. If their pressure dropped at the same time, the utility may be working on the main in your street.

  • One fixture weak: a clogged aerator or shower head, or a failing cartridge
  • Hot side weak everywhere: sediment in the water heater, or a partly closed valve at the heater
  • Whole house weak, gradually: a failing pressure-reducing valve, narrowed pipe, or a partly closed main
  • Whole house weak, suddenly: a leak or break, or a utility issue

What can I check myself?

Clean the aerator or shower head, make sure the main shutoff is fully open, and check the meter for a leak.

Unscrew the aerator from the end of a weak faucet. If it is packed with white grit, soak it in vinegar, rinse it and screw it back on. Shower heads can be soaked the same way. Arizona's hard water clogs these small screens steadily, so this solves a lot of single-fixture pressure problems.

If the whole house is weak, check that the main shutoff valve is fully open, especially if someone recently worked on the plumbing. Then run the meter test from our hidden leak guide, because a leak can steal pressure from the rest of the house.

What does the plumber check first?

We measure static pressure at a hose bib, check the pressure-reducing valve and the main shutoff, and look at the condition of the pipes.

A gauge on an outdoor hose bib shows the pressure entering the house. Many homes have a pressure-reducing valve, usually near the main shutoff, that holds pressure in a safe range. When that valve fails, it can drop pressure too low or let it climb too high. Either way, it is a single part that can be replaced.

If the pressure entering the house is fine but the fixtures are still weak, the pipes themselves may be the problem. Older galvanized steel pipe corrodes on the inside and narrows over time, and scale can do the same in other materials. Our guide to signs you need repiping covers the other warning signs.

What are the fix options?

Clean or replace the fixture parts, replace a failed pressure-reducing valve or shutoff, or repipe when the pipes themselves have narrowed.

Fixture-level problems are a faucet and fixture repair. A failed pressure-reducing valve or main shutoff is a piping repair. When corroded pipe is the cause, repiping with copper or PEX-A restores full flow. Our guide to copper vs. PEX vs. PVC explains the materials.

Three Clear Options. No Pressure. You see each option with upfront pricing and approve one before any work begins. Financing Options Available through GreenSky for larger work like repiping.

Quick answers

Can water pressure be too high?
Yes. High pressure strains fixtures, supply lines and appliances, and it is a common reason toilets run and faucets drip. A pressure check at the hose bib tells you where you stand.
Will a water softener lower my water pressure?
A properly sized softener should not noticeably reduce pressure. If pressure dropped after a softener went in, it may be undersized, clogged or set up wrong, and it is worth having it checked.
Why is only my hot water pressure low?
Sediment in the water heater or a partly closed valve at the heater are the usual causes. A flush or a valve repair often fixes it.

Next step

Pressure weak everywhere, or just in one shower? Book a visit and we will measure it and find the cause.

Schedule service
Call now Book online